95 Griff random wires
Discussion
That’s really good. The map switch with mot made me smile 
I’ve spent all my budget so I’m making good with what I have unfortunately. Anything damaged I’ll repair/replace accordingly. My engine has been tuned but it’s old skool now which I’m happy with. Maybe the next owner will do the ecu change who knows
With regards to stereo I’m fitting a pair of slim mount 8” subs in enclosures behind the seats and under the centre console area. The amp will be mounted on the panel with the rear vents but in the boot. That’s my plan. I’ll put the pictures and more detail in the restoration thread when I’m doing that.
It’s the mass of wires I’m working through here.
Ideally I’d like nothing on the battery when finished. So it’s an easy slide in or out affair.
I’m also looking at doing some wiring mods to the electric window feeds and wipers so they actually move effectively rather than laboured.
Yeah lots to chip away at still
I’ve spent all my budget so I’m making good with what I have unfortunately. Anything damaged I’ll repair/replace accordingly. My engine has been tuned but it’s old skool now which I’m happy with. Maybe the next owner will do the ecu change who knows
With regards to stereo I’m fitting a pair of slim mount 8” subs in enclosures behind the seats and under the centre console area. The amp will be mounted on the panel with the rear vents but in the boot. That’s my plan. I’ll put the pictures and more detail in the restoration thread when I’m doing that.
It’s the mass of wires I’m working through here.
Ideally I’d like nothing on the battery when finished. So it’s an easy slide in or out affair.
I’m also looking at doing some wiring mods to the electric window feeds and wipers so they actually move effectively rather than laboured.
Yeah lots to chip away at still
Good luck with the stereo install. Having spent ages looking at other installs and planning my stereo upgrade I thought I’d want a sub in the system. In the end I was headed toward an enclosure self built to sit in the boot above the tank integrated into the panel, so no loss of space or cutting - as low freq sound is less directional I could fire them in to the boot space…. But, having built the system and listened to it, I don’t need a sub.
I went with ….
Tempo Ultegra Integra 602’s in the doors
Tempo Ultegra Integra 502’s in the rear shelf
Focal 4.350 amp in the footwell
Pioneer AVH7200DAB head unit
It took an absolute age to find speakers at 165mm where the housing/grille would fit neatly into the doors with only a small opening to the existing hole and wasn’t awful looking. The Morels are perfect and also have recessed tweeters - less directionally sensitive - than others.
I went with 2 ways front and rear as I didn’t want separately mounted tweeters spoiling the aesthetics. I also didn’t want the headache of finding more space to mount passive crossovers or a DSP for separates. I use the HU crossover to control frequency backed up by the amps settings.
The 502’s fit exactly into the vent holes in the bulkhead. No cutting required. Amp driven, they offer more than enough power for such a small cabin.
I have focal speakers in my home system, but couldn’t get the sizes I wanted for the TVR, but the amp is a perfect fit into the footwell on the plinth and is sufficient to drive the system. Especially with such a small cabin area.
New speaker wiring throughout, run through sill etc.
HU with pop out screen I managed to get fitted without a spacer. Condition was to be able to have SatNav without a stick job on the screen again with Airplay etc.
When I did the maths for enclosure sizes for an 8” sub, there simply wasn’t anywhere in the cabin I could fit one and even the under seat units are 300x250x75 typically - housing an amp as well.
Looking forward to see your solutions for the subs.
I went with ….
Tempo Ultegra Integra 602’s in the doors
Tempo Ultegra Integra 502’s in the rear shelf
Focal 4.350 amp in the footwell
Pioneer AVH7200DAB head unit
It took an absolute age to find speakers at 165mm where the housing/grille would fit neatly into the doors with only a small opening to the existing hole and wasn’t awful looking. The Morels are perfect and also have recessed tweeters - less directionally sensitive - than others.
I went with 2 ways front and rear as I didn’t want separately mounted tweeters spoiling the aesthetics. I also didn’t want the headache of finding more space to mount passive crossovers or a DSP for separates. I use the HU crossover to control frequency backed up by the amps settings.
The 502’s fit exactly into the vent holes in the bulkhead. No cutting required. Amp driven, they offer more than enough power for such a small cabin.
I have focal speakers in my home system, but couldn’t get the sizes I wanted for the TVR, but the amp is a perfect fit into the footwell on the plinth and is sufficient to drive the system. Especially with such a small cabin area.
New speaker wiring throughout, run through sill etc.
HU with pop out screen I managed to get fitted without a spacer. Condition was to be able to have SatNav without a stick job on the screen again with Airplay etc.
When I did the maths for enclosure sizes for an 8” sub, there simply wasn’t anywhere in the cabin I could fit one and even the under seat units are 300x250x75 typically - housing an amp as well.
Looking forward to see your solutions for the subs.
Well stereo plan is as follows
Alpine cdm-7892 up front. Was looking for a pioneer prs 80 but a good deal was had on the alpine unit.
Front speakers are new old stock kicker 5 1/4” components. I’m using slightly smaller units as I hate chasing door rattles so as I’m cutting frequencies there is no point in big front speakers.
Tweeters will be mounted where the door ashtray currently resides. I’m fitting all new trim so I’ll repair the ashtray holes and fit the tweeters nicely first.
Those will be run via an active crossover. The pioneer unit does this using it’s built in pre-outs. Haven’t got that now so a stand alone unit will be used. I have a nice kenwood unit to do that. Not sure where to mount that as yet. Because it’s Kenwood I want it hidden from view so the system looks just Alpine and kicker.
Then I have 2 new old stock kicker resolution 8” shallow mount subs. Rather than waste space making a complete enclosure, I will bond directly to the fibreglass body. Exact enclosure sizes still to be measured but that’s how I’m doing it. Again I’ll trim and carpet accordingly as it will all be new.
Amplifier is a new old stock kicker impulse 6 channel to be mounted in the boot behind the rear speaker/vent panel.
A very simple system but run active. The alpine headunit also has a time alignment facility so I can use that and fine tune everything using h/u and amplifier crossovers.
Then for a bit of old skool nostalgia a cd changer, alpine to replace the original pioneer unit.
All new cables will be used and all hidden. especially on the amplifier. The dash gauges will have the illumination changed to green to match the alpine h/u.
The rear speaker/vent holes I’ll cover with a pair of perforated leather covers to match the new trim.
In theory I should have a nice punchy bass/sub bass sounding system rather than a low rattling sub bass system.
With the roof down you will only see the door speakers. Nothing outrageous. I’m after a sort of 90’s-2000’s factory upgrade look.
That’s the plan
Alpine cdm-7892 up front. Was looking for a pioneer prs 80 but a good deal was had on the alpine unit.
Front speakers are new old stock kicker 5 1/4” components. I’m using slightly smaller units as I hate chasing door rattles so as I’m cutting frequencies there is no point in big front speakers.
Tweeters will be mounted where the door ashtray currently resides. I’m fitting all new trim so I’ll repair the ashtray holes and fit the tweeters nicely first.
Those will be run via an active crossover. The pioneer unit does this using it’s built in pre-outs. Haven’t got that now so a stand alone unit will be used. I have a nice kenwood unit to do that. Not sure where to mount that as yet. Because it’s Kenwood I want it hidden from view so the system looks just Alpine and kicker.
Then I have 2 new old stock kicker resolution 8” shallow mount subs. Rather than waste space making a complete enclosure, I will bond directly to the fibreglass body. Exact enclosure sizes still to be measured but that’s how I’m doing it. Again I’ll trim and carpet accordingly as it will all be new.
Amplifier is a new old stock kicker impulse 6 channel to be mounted in the boot behind the rear speaker/vent panel.
A very simple system but run active. The alpine headunit also has a time alignment facility so I can use that and fine tune everything using h/u and amplifier crossovers.
Then for a bit of old skool nostalgia a cd changer, alpine to replace the original pioneer unit.
All new cables will be used and all hidden. especially on the amplifier. The dash gauges will have the illumination changed to green to match the alpine h/u.
The rear speaker/vent holes I’ll cover with a pair of perforated leather covers to match the new trim.
In theory I should have a nice punchy bass/sub bass sounding system rather than a low rattling sub bass system.
With the roof down you will only see the door speakers. Nothing outrageous. I’m after a sort of 90’s-2000’s factory upgrade look.
That’s the plan
Looking forward to seeing it done! I don’t have ash trays, if I had I would have considered a recessed tweeter mount in the space and modded the cards accordingly ahead of its retrim. But no existing holes and wishing to keep it as subtle as I can I opted for coax’s with a recessed tweeter as a compromise.
I do think running a DSP is a good solution as it allows the control of all elements from crossovers to phasing, time alignment etc. The Pioneer unit I have is good, with all elements covered, but it’s also limited. Perfectly adequate for my system via pre-outs. I nearly extended the budget for an amp with integrated DSP, but space and cost - plus a dose of healthy realism of what could be achieved meant I stepped back. I also really wanted it hidden in the footwell.
Similar to you I wanted a subtle system, without horrible looking speaker installs with crap looking grilles etc. I went 165 fronts to make the most of the 2 ways and get the lower frequency response, running with a 50hz HPF, 80 for the rears. They do reach lower, but not sub levels! The rears you’d hardly notice versus existing vents.
Door cards treated with sound deadening and all loose wires etc checked to eradicate any rattles. Will treat rear bulkhead when it’s back home.
Are you going to use the rear earthing point location behind the fuel tank for the amp? Saves a lot of additional cabling?
I do think running a DSP is a good solution as it allows the control of all elements from crossovers to phasing, time alignment etc. The Pioneer unit I have is good, with all elements covered, but it’s also limited. Perfectly adequate for my system via pre-outs. I nearly extended the budget for an amp with integrated DSP, but space and cost - plus a dose of healthy realism of what could be achieved meant I stepped back. I also really wanted it hidden in the footwell.
Similar to you I wanted a subtle system, without horrible looking speaker installs with crap looking grilles etc. I went 165 fronts to make the most of the 2 ways and get the lower frequency response, running with a 50hz HPF, 80 for the rears. They do reach lower, but not sub levels! The rears you’d hardly notice versus existing vents.
Door cards treated with sound deadening and all loose wires etc checked to eradicate any rattles. Will treat rear bulkhead when it’s back home.
Are you going to use the rear earthing point location behind the fuel tank for the amp? Saves a lot of additional cabling?
Johno said:
Looking forward to seeing it done! I don’t have ash trays, if I had I would have considered a recessed tweeter mount in the space and modded the cards accordingly ahead of its retrim. But no existing holes and wishing to keep it as subtle as I can I opted for coax’s with a recessed tweeter as a compromise.
I do think running a DSP is a good solution as it allows the control of all elements from crossovers to phasing, time alignment etc. The Pioneer unit I have is good, with all elements covered, but it’s also limited. Perfectly adequate for my system via pre-outs. I nearly extended the budget for an amp with integrated DSP, but space and cost - plus a dose of healthy realism of what could be achieved meant I stepped back. I also really wanted it hidden in the footwell.
Similar to you I wanted a subtle system, without horrible looking speaker installs with crap looking grilles etc. I went 165 fronts to make the most of the 2 ways and get the lower frequency response, running with a 50hz HPF, 80 for the rears. They do reach lower, but not sub levels! The rears you’d hardly notice versus existing vents.
Door cards treated with sound deadening and all loose wires etc checked to eradicate any rattles. Will treat rear bulkhead when it’s back home.
Are you going to use the rear earthing point location behind the fuel tank for the amp? Saves a lot of additional cabling?
I enjoy the challenge when fitting car audio. So getting a good sound in an open top car is difficult. The kicker speakers I have have lovely plain black cones, grilles and a subtle badge. The mesh grille is of the full speaker type not a later funky kicker style. I do have a second set of matching 4” components and toyed with 8” door mounted woofers with the 4” components but it would be too much and not very tasteful. I do think running a DSP is a good solution as it allows the control of all elements from crossovers to phasing, time alignment etc. The Pioneer unit I have is good, with all elements covered, but it’s also limited. Perfectly adequate for my system via pre-outs. I nearly extended the budget for an amp with integrated DSP, but space and cost - plus a dose of healthy realism of what could be achieved meant I stepped back. I also really wanted it hidden in the footwell.
Similar to you I wanted a subtle system, without horrible looking speaker installs with crap looking grilles etc. I went 165 fronts to make the most of the 2 ways and get the lower frequency response, running with a 50hz HPF, 80 for the rears. They do reach lower, but not sub levels! The rears you’d hardly notice versus existing vents.
Door cards treated with sound deadening and all loose wires etc checked to eradicate any rattles. Will treat rear bulkhead when it’s back home.
Are you going to use the rear earthing point location behind the fuel tank for the amp? Saves a lot of additional cabling?
The earth point in the boot I didn’t know about. I’ll be removing the fuel tank to trim the boot again which then allows fitment of the amplifier and associated cables. The fuel tank I’m thinking I might use the interior colour vinyl and I might stitch that to match the seat insert tuck and roll pattern. If the tank is out it wouldn’t take long to cover it.
So lots of ideas at the moment
Gassing Station | Griffith | Top of Page | What's New | My Stuff